Pressure distribution data from tests of 2.29-meter (7.5-ft.) span EET high-lift research model in Langley 4- by 7-meter tunnel
Read Online
Share

Pressure distribution data from tests of 2.29-meter (7.5-ft.) span EET high-lift research model in Langley 4- by 7-meter tunnel

  • 429 Want to read
  • ·
  • 81 Currently reading

Published by National Aeronautics and Space Administration, Langley Research Center in Hampton, Va .
Written in English

Subjects:

  • Transport planes.,
  • Airplanes -- Fuel systems.

Book details:

Edition Notes

StatementHarry L. Morgan, Jr.
SeriesNASA technical memorandum -- 83111.
ContributionsLangley Research Center.
The Physical Object
FormatMicroform
Pagination1 v.
ID Numbers
Open LibraryOL17666081M

Download Pressure distribution data from tests of 2.29-meter (7.5-ft.) span EET high-lift research model in Langley 4- by 7-meter tunnel

PDF EPUB FB2 MOBI RTF

Chapter 2 • Pressure Distribution in a Fluid 73 For the linear law to be accurate, the 2nd term in parentheses must be much less than unity. If the starting point is not at z = 0, then replace z by δz: Denver, Colorado, has an average altitude of ft. On a U.S. standard day, pres-sure gage A reads 83 kPa and gage B reads Size: 1MB. mean systolic blood pressure was mm Hg with a standard deviation of We wish to know if on the basis of these data, we may conclude that the mean systolic blood pressure for a population of African-American is greater than Use α= Text Book: Basic . A-4 The “net limit pressure,” pL*, is used in foundation design, and is calculated using equation A pL* = pL – pho (eq. A-2) where: pL = limit pressure; and pho = initial total horizontal pressure in the ground. = [(γ-u)z ] Ko + u Although pho should equal the pressure corresponding to vo (i.e. value corresponding to po), it is difficult to accurately determine po from the test data File Size: KB. The PMT operator may expand the pressuremeter probe in equal pressure increments (stress controlled test) or in equal volume increments (strain controlled test) (Figure 2), typically stopping the test when initial volume of the probe has doubled or when reaching the maximum allowable pressure. About 40 data points are obtained from a strain.

Statistics for Analysis of Experimental Data Catherine A. Peters Department of Civil and Environmental Engineering Princeton University Princeton, NJ Statistics is a mathematical tool for quantitative analysis of data, and as such it serves as the means by which we extract useful information from data. Further readings can be taken as the pressure is lowered to provide data for the imbibition case from Swi to Cp = 0 at point A in Figure The volume of mercury injected into the pores at a given pressure is usually expressed as a proportion of the total pore space, and is presented as a pore size distribution . has a large selection of pressure data loggers for the measurement and monitoring of barometric, gauge and atmospheric pressures up to 5, PSI. These pressure data logging recorders are available with multiple pressure ranges, lcd display, alarms, direct . Pressure gauges are used to determine absolute pressure (excess and negative) relative pressure for air, gases and/or liquids. When a measurement for absolute pressure is taken in a closed system, consideration must be given to the absolute pressure outside the system being measured, so choose the pressure gauges that best suits this purpose.

Field Test Procedures for Protective Relays and Associated Circuits Previously Titled: searching existing data sources, gathering and maintaining the data needed, and completing and reviewing this collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including. distribution, i.e., weather or not it deviates from the assumed distribution. Some tests are for a single outlier and others for multiple outliers. Selection of these tests mainly depends on numbers and type of target outliers, and type of data distribution.1 Many various tests according. The data in Table 1 are actually sorted by which distribution fits the data best. The next section describes how this was determined. Determining Which Distribution Fits the Data Best. The second part of the output is used to determine which distribution fits the data best. Table 2 shows that output. Each column is described below. include at least the following topics: introduction (Chapter 1), basic probability (sections and ), descriptive statistics (sections and ), grouped frequency.